This is a way doctors use special tools to hold teeth steady while they move. Think of it like using a rope to keep a tooth from moving too fast or in the wrong direction during braces. It helps the braces work properly.
Every report comes from a Lived member, sent anonymously.
No reports yet
Add what worked for you with the search bar below
Anchorage is how an orthodontist keeps some teeth from moving while pushing or pulling others into place. Every force that braces or aligners put on a tooth pushes back on whatever it is attached to, so without a stable anchor the teeth meant to stay put can drift and undo part of the correction. Traditionally, anchorage comes from groups of back teeth, the roof of the mouth (the palate), or headgear worn outside the mouth. An orthodontic anchorage procedure usually means placing a temporary anchorage device (TAD). This is a very small screw, often called a miniscrew or mini-implant, set through the gum into the jawbone so it acts as a fixed point that does not move. It can help with movements that braces alone handle poorly, such as pulling front teeth back after extractions, moving back teeth forward or backward, pushing over-erupted teeth up into the bone, or uprighting tipped teeth. TADs work with fixed braces and with removable appliances, including aligners. Larger bone-anchored plates in the palate are used in some cases. The main appeal is that a TAD does not depend on the person wearing headgear or elastics faithfully. Many treatments never need one; whether it is worth adding depends on the movements planned and how much anchorage the usual methods can supply.
The orthodontist explains why a TAD is being considered and where it will go. Dental X-rays are used to check the space between tooth roots and the thickness of the bone at the chosen site, and some practices add a 3D scan called cone-beam CT (computed tomography) to plan the position more precisely. Common sites are between the roots of upper or lower back teeth and in the roof of the mouth. Tell the orthodontist about your medical history, medicines and any past reactions to dental numbing medicine. Ask whether to take a pain reliever beforehand: in one small trial, a dose of ibuprofen about half an hour before placement reduced soreness over the following hours. Arrangements are usually simple, since placement uses local numbing rather than sedation.
The area is numbed first, either with a strong numbing gel on the gum or with a small injection of local anesthetic. Limited studies suggest the injection gives the least discomfort, though it means a needle; numbing gel avoids that but can leave more sensation. The person stays awake. The orthodontist or surgeon then turns the miniscrew through the gum into the bone. Most people feel pressure. A sharp or rising sensitivity during placement can mean the screw is near a tooth root, so it is worth saying so right away. Once the screw is in place, springs, elastic chains or wires connect it to the braces or appliance, either at the same visit or later.
Soreness around the screw is common for the first day or so. In a study of teenagers and young adults with screws in the roof of the mouth, typical pain had faded to nothing by about a day and a half, and ordinary pain relievers such as acetaminophen (Tylenol) were enough. The head of the screw can rub the cheek or tongue at first; orthodontic wax or a cover over the head helps. The screw stays for as long as that stage of treatment needs it. Keeping the gum around it clean matters, because plaque there can lead to inflamed or overgrown tissue. Follow the orthodontist's instructions for cleaning around it. Contact the orthodontist if the screw feels loose, if the gum around it becomes swollen, painful or keeps bleeding, or if a tooth next to it stays sore or sensitive. Taking the screw out is usually a minor step; the small hole left behind heals over on its own.
The most common problem is that the screw loosens or fails before treatment is finished. In a large analysis of nearly 5,000 miniscrews, about 13.5% failed, or roughly 1 in 7. A loose screw can usually be removed and replaced, sometimes in a different spot, but it can delay that stage of treatment. Failure was not linked to age or sex, but it varied with which jaw held the screw, and screws that end up touching a tooth root are much more likely to fail. Contact with the root of a neighboring tooth is the most frequently reported complication. Most of this minor damage heals once the screw is taken out promptly. Rarely, an injured tooth loses its nerve supply or needs root canal or surgical treatment. Other risks depend on the site: irritation or minor infection of the gum around the screw head, a small opening into the sinus from screws high in the upper back jaw (usually heals on its own), and, rarely, nerve injury in the lower jaw causing numbness, which careful planning is meant to avoid. A screw can occasionally break during placement or removal. Removal sometimes leaves a small scar on the gum. On the benefit side, a Cochrane review of 15 randomized trials found moderate-quality evidence that screws and other bone anchors hold the back teeth in place better than conventional anchorage, by about 1.7 mm on average. That can be the difference between closing a gap fully and losing part of the correction. There was no clear evidence that TADs shorten overall treatment time, and the trials gave little information on pain or how acceptable people found them.
Last reviewed • Oct 2026
Educational content, not medical advice.
Share your experience with Orthodontic Anchorage, what to expect, or ask the community a question.